News of My CPU isn't recognized

On my PC-Chips 830LR, flashed with CheepoMan's modded final release of the ECS K7S5A (non-Pro) BIOS, it will not POST with the FSB/RAM set to 133/133 with an Athlon MP 1800+.

An Athlon MP 1600+ works just fine at that setting, it doesn't POST if the FSB/RAM are *not* the same frequency.

When I swapped CPUs, the setting switched itself to 100/100. I don't know why when the only difference between these two Palomino core ...

Hello,
I've got Acer Aspire L5100, with AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ (AM2 socket). One of it's features is AMD-V (virtualization hardware support).

My operating system (linux, kernel 2.6.27-9) perfectly recognizes the cpu and it's capabilities but when I try to actually activate the virtualization support it fails, saying "Disabled by BIOS". I checked all BIOS menus and there is no such option.
The BIOS is AwardBios, version R01-B0. "System version:" 6.00. ...

HI
I have Asus P5PL2-E motherboard based on i945G chipset :
http://www.asus.com/products.aspx?l1=3&l2=11&l3=194&model=1478&modelmenu=2
and I use this AMI Bios file :
http://dlsvr04.asus.com/pub/ASUS/mb/socket775/P5PL2-E/P5PL2-E-ASUS-1002.zip
I like to make support for 45nm cpu E5200 and I don't know how to do it.
On asus forum they have told me that it is not supported because motherboard VRD is version 11.0 and it should be 11.1.
BUT I think they don't like to make support for it because I have ...

I have managed to find a website which pin mods the Conroe-L (LGA775, Celeron 400 Series CPU) to power it up.

I have also done some research and grabbed microcode files for those CPUs. (CPUID 10661h) and I understands that Intel D945GCZ uses EFI format AMI bios.

Is it possible to inject the microcode for Conroe/L into this EFI formatted BIOS? Please shed a light on the names of possible websites and/or tools that can ...

I got given another truckload of PCs to wreck out a few weeks ago, & in
amongst them was a Flytech book sized pc, or so it's called, that had a
200mhz IBM cpu in it, & no memory...
I saw it had a VIA vp382c598 chipset & got to thinking that it should run
100 fsb...
So after searching for the manual for the board in it, { A68 V1.1} I found
it does ...

This is the message that I am getting on my Dell GX280 mini tower. I had my motherboard go out and replaced it with another with the same part #. The new board will run with a 2.8 G CPU but not with the original 3.6 G CPU. I have tried everything that I can think of and it is still not working.

I have done the following:

1. Rest the CMOS many times.
2. ...

can someone give me a hand to add new microcodes(45nm) in my bios??
my board is GA-8I865PE775-G-RH(6.6)
my cpu is qx9650 and e8400
when i use qx9650 the bios will show ukown ID and the speed is 200X6 and even i change the multiplier in bios it will not work in other multiplier(only 6)
then i use this cpu in windows the cpu-z show qx9650 but the speed is 1200
can someone solve my problem ...

http://www.gigabyte.com.tw/Support/Moth ... uctID=1449

good morning @all

I have that above mentioned mainboard running fine with Lin Lin S370 converter and Tualatin PIII-S 1400
http://processorfinder.intel.com/detail ... Spec=SL6by

the only aesthetically point is that Tualatin CPUs will be shown as Xeon CPUs @boot up

so is there any mod bios known containing Tualatin microcodes ?

thank you for reading

I've tried to know my motherboad cpu support limit, it confusing me, either.

Below is my motherboad cpu micro code info, could you tell me below cpu id meaning?
and cpu support limit ?


1. 478pin Celeron D :
2. northwood p4 :
3. fsb533 prescott p4 :
4. fsb800 prescott p4 :

** Micro Code Information **
Update ID CPUID | Update ID CPUID | Update ID CPUID | Update ID CPUID
------------------+--------------------+--------------------+------------------- ...

CPU upgrade issue. Sorry can't attach jumper settings
from manual.

I purchased a mobile Athlon XP with a Barton Core
Model # - AXMA2600FKT4C

Installed in the mobo and posts as a Mobile Athlon 800MHz

The mobo auto detects the part at six times multiplier.
The mobo has DIP switches for setting the FSB and the multiplier.

The mobo is set a FSB 133MHz and the multiplier set at auto.

Problem - When set as ...