Uniflash and Bootblock Mismatch warning

Discusses BIOS flashers and utilities from Award, AMI and Uniflash
Post Reply
Denniss
BIOS Guru
Posts: 3153
Joined: Thu Mar 21, 2002 8:16 pm
Location: Near Hannover (CEBIT) Germany
Contact:

If using Uniflash to flash a mainboard's Bios you might get a "Bootblock Mismatch" error message with the option to continue flashing or not
Do not continue flashing !!
> It may render your Bios useless or (with luck)the board starts with emergency Bios (Bootblock Bios)

Make sure you have the correct Bios !

If you get this "Bootblock Mismatch" error message do not continue flashing - go to Uniflash Advanced menu and use the option Flash including bootblock - if the message comes again press Y and continue ( Bootblock and main Bios are updated)
Last edited by Denniss on Fri Jul 18, 2003 7:48 pm, edited 1 time in total.
ajzchips
El cheapo dude
Posts: 3048
Joined: Sat Mar 23, 2002 12:41 pm
Location: Madrid, Spain

Very true. I always ended up with a dead board when I got that warning and proceeded anyhow. I believe Rainbow mentioned he was going to do something about this issue.
Rainbow
The UniFlasher
Posts: 3122
Joined: Wed Mar 20, 2002 4:16 pm
Location: Slovakia
Contact:

v1.30 will include another question if there's mismatch - if you answer Y that you want to flash, it will ask you if you want to flash including bootblock, Y is recommended.
v1.3 will also show the progress bar in green or red. Green when block was flashed OK, red when there was an error (such as timeout).
Patched and tested BIOSes are at http://wims.rainbow-software.org
UniFlash - Flash anything anywhere
Denniss
BIOS Guru
Posts: 3153
Joined: Thu Mar 21, 2002 8:16 pm
Location: Near Hannover (CEBIT) Germany
Contact:

Uniflash has now reached version 1.32

Available on the new Website www.Uniflash.org
KachiWachi
The New Guy
Posts: 1451
Joined: Fri Mar 29, 2002 10:32 pm
Location: Pennsylvania, USA

You may move this to it's own thread if appropriate...

Suppose you get this error, flash the bootblock, but in reality you've chosen the wrong file to flash to begin with. I would guess not all bootblocks are the same. Wouldn't that still render your board useless??
ruelnov
Master Flasher
Posts: 172
Joined: Tue Jun 08, 2004 2:11 pm
Contact:

Very true, and I have learned from this experience.

And to make sure that I'm flashing the correct BIOS file or correct BIOS update, I first save the existing ROM binary file, then compare it with the new file to be flashed based on the following parameters:
1. BIOS ID String (without the release date),
2. Chipset Register Defaults,
3. IRQ Routing Table,
4. ACPI Table

These parameters don't change as new BIOS updates are being released by the manufacturer for the same board.

Wouldn't it be great if Rainbow could include this "auto-compare feature" in future versions of Uniflash?
Rainbow
The UniFlasher
Posts: 3122
Joined: Wed Mar 20, 2002 4:16 pm
Location: Slovakia
Contact:

Functionality like "auto-compare" will NOT be implemented. UniFlash should be universal - it does not check what's inside the file you are flashing - it only checks the size, which must always be equal to the size of the chip.
BTW.: Starting with v1.33, flashing is done including bootblock by default.
Patched and tested BIOSes are at http://wims.rainbow-software.org
UniFlash - Flash anything anywhere
geni01
BIOS Newbie
Posts: 18
Joined: Sun May 15, 2005 4:47 am

HI, I just try to use Uniflash to flash my mobo P4c800-E deluxe, and this message comes up :

Flash Data Verification Error
Retry Write Operation [Y/n]

When I try it again, it's always comes up with this error message.

Help pleaseeeee :cry: :cry: :cry:
franka2
New visitors - please read the rules.
Posts: 13
Joined: Mon Dec 12, 2005 4:07 am

you may run into this prob if u picked up a mobo from inferior manufacturer ... ;)

the smartest guys have ELITEGROUP featuring TOP HAT FLASH

a socket to flip over soldered on PLCC / bad bootblock no problem whatsoever!

check out for youself - it's pretty much a failproof concept "by design"...
Post Reply