M530 motherboard bios chip help
hi Yezok that is so cool.on the willem program on device when programming i dont see the cat28f010 chip
willem supported devices list
28f010 <----- pick this one on the willem programmer to flash?
MX28F1000P
SST 29EE010
Winbond 29EE011
ATMEL 29C010
Intel 28F001 BX-T120 <--- i didnt see this one on the device listing
thanks again
cee710
willem supported devices list
28f010 <----- pick this one on the willem programmer to flash?
MX28F1000P
SST 29EE010
Winbond 29EE011
ATMEL 29C010
Intel 28F001 BX-T120 <--- i didnt see this one on the device listing
thanks again
cee710
Yes to program the CAT28F010 select the 28F010 then click the ? for device ID
It must return
Manufacture Code 0x31 CATALYST
Device Code 0xB4 CAT28F010
I it does not then you may the have switch setting jumpers wrong, recheck and try again.
To program 28F001BX-T select from the menu Flash 28Fxxx > 28F00x 8Bit and the top one on the list if you are using software 0.97G or 0.97JA.
You will also need to set the jumper that shorts pin 1 to pin30 on the programmer.
Where did you get a Ver 5.0 programmer, It must not be a true Willem, the last time I check the latest version was 4.5 with TSOP ZIF Socket.
I did not see a 5.0 Version in the programmer shop on the site.
It must return
Manufacture Code 0x31 CATALYST
Device Code 0xB4 CAT28F010
I it does not then you may the have switch setting jumpers wrong, recheck and try again.
To program 28F001BX-T select from the menu Flash 28Fxxx > 28F00x 8Bit and the top one on the list if you are using software 0.97G or 0.97JA.
You will also need to set the jumper that shorts pin 1 to pin30 on the programmer.
Where did you get a Ver 5.0 programmer, It must not be a true Willem, the last time I check the latest version was 4.5 with TSOP ZIF Socket.
I did not see a 5.0 Version in the programmer shop on the site.
hi Yezok i bought it from a ebay user a few months ago
this is the pic
http://family.webshots.com/photo/230547 ... 6932PLqvyr
i dont know if its a true willem programmer.there is 2 jumpers (j4) pb5.0c and pb3 move jumper (j4) to make it work as pb3 for epr097 and ep097g. i have flashed a sst39sf040 pllc32 chip for my laptop and it worked.had a bad flash.had to unsoilder the old chip i put a pllc32 socket on it after it.its a hp palivion ze4560us.(amd)
i have another mb asus cusl2 with a corrupted bios i have to unsolider the pllc32 chip on that also that chip is a intel N82802AB8 i hope the chip can be reprogrammed.or ill try to serach for it if its aviable.
cee710
this is the pic
http://family.webshots.com/photo/230547 ... 6932PLqvyr
i dont know if its a true willem programmer.there is 2 jumpers (j4) pb5.0c and pb3 move jumper (j4) to make it work as pb3 for epr097 and ep097g. i have flashed a sst39sf040 pllc32 chip for my laptop and it worked.had a bad flash.had to unsoilder the old chip i put a pllc32 socket on it after it.its a hp palivion ze4560us.(amd)
i have another mb asus cusl2 with a corrupted bios i have to unsolider the pllc32 chip on that also that chip is a intel N82802AB8 i hope the chip can be reprogrammed.or ill try to serach for it if its aviable.
cee710
You will not have much luck programming the cat28F010 with out an external power supply with that programmer.
You can program the Intel N82802AB8 with it. it is a firmware hub and it is in the menu you just put it in the firmware hub LPC socket and set up the programmer accordingly.
you should always use an external power pack with that programmer
You can program the Intel N82802AB8 with it. it is a firmware hub and it is in the menu you just put it in the firmware hub LPC socket and set up the programmer accordingly.
you should always use an external power pack with that programmer
hi i recieved my cat28f010 today just to let you guys know i reprogrammed it with the 5201016s.bin with epr097ja and it works great :0) thank you so much for all your time and help i couldnt of done it with out your help. thank you again.
cee710
cee710