BIOS Updates forum

I believe that if all the pins have the same function, there would be no problem.. What do you think sharedoc? BTW I got another mobo for my 600E, and true enaugh, it was a later version than the one I modded, the P3 600mhz got in right away.. But a problem with the cache memory of course.. But that...

Awsome, is the fbs66 or 100mhz?

Interesting, I have never seen a Celeron with that kind of Mhz in MMC-2 . . Better watch that. True it would be easier to fit than a P3 in this case, but I'm stubborn. heheh But, I'm gonna be watching for both kinds for sure

I have the plain and simple PC66-32mb onboard crap, plus 1 stick 64mb PC100 for testing purposes.. I tried with both processors, and it won't powerup with the P3, but powers up with the P2. Now that I think of it I replaced that processor a while back now in my 600X because of that. Small brain that...

I tried to go with a 1k resistor from #48 to #25, and tested the voltage, there was 2.6v. So I proceeded with the boot with the P3-500mhz, and by the time windows finished loading, the screen went blank and the thing powered itself off. I had the thing in front of me, and no smoke no nothing, lol Ho...

The marking of the resistors are not marked the same, since my motherboard differs a little bit from that one, but I can still manage to figure out what is what comparing the 2 of them. BUT, I just want to make sure I'm on the right track. On the picture that Katch provided on the link you provided,...

From pin#25, looking at the motherboard the same way you can look at it on the picture, the tiny folio that goes south-east for a little over a quarter inch and then passtrough, I toke the passtrough just next to it as a reference point, but doesn't appear on the frontside of the motherboard. On the...

So sharedoc, did the pictures helped? I just got back from work, and now need to wait for the wife to get back with the car so I can buy a new supply of resistances and stuff..

From the MMC-2 I can not find any folio going from 34B to - .. There's not folio connecting to it. My wild guess is that there is a folio under the white MMC-2 piece itself, or I don't have the right pin, which would be not likely. It is the morning here, gotta go to work, but when I get back I'll t...

BTW, I got a picture of the backside of the board and the front side (Clock generator area), want me to send 'em to ya?

Voltages ... Well, with both PII 300mhz or PIII 500mhz, they stay at praticaly 0 .. I don't have a digital multi-meter, but it still a good one (I'm old fashion, like the gauge better than digital .. yes im weird :D ) , position 2.5volt sensibility, and my gauge barely moves, my wild guess is that t...

Nevermind I found it .. Yes I have resistance between 34B and Pin#25 . . My tester read about 5 ohms, but the selector says x10, would make it 50ohms .. that much? Heh Resistance betweek 34B and ground = 31x10= 310ohms Now I'm gonna power it on and measure the power coming from #25 with the PII and ...

how can i find pin 34B just tell me how to find pin 1A and im gonna be aight

The clock generator I got on my board differs a little bit, but I think it is still the same thing tho .. Marked: SG577DYB, under that markings go as: 9839 f5120 My board is hell of a lot different than the one on the link (The 770X one) If I had a place to post pictures, I would post a few to show ...

Well well well, this is what I call picking my curiosity muahaha
Proceeding right now with the screw driver to take it appart, and see what I can do, get back to you if I run trough a problem!