CMOS SETTINGS WRONG

Is your memory not fully recognized? (Intel VX chipset Memory recognition)
Post Reply
mkmir
New visitors - please read the rules.
Posts: 2
Joined: Thu Oct 31, 2002 4:14 pm

Help!!!!!!!

First, excuse my Bad english.

Probleme : when I switch on my computer, I have this message : CMOS SETTINGS WRONG. If I put F2 ( load defaults sttings), that's ok. Winxp and all programs.

But if I put F1 ( modifie bios setup), and F10 ( whitout any chanage), My computer doesn't switch on ( it's blocked). Whitout any message.

Of course, I changed Bios, but always the same thing.

I have this configuration

MC : MSI KT3 Ultra2 Socket A VIA KT333
Processor : AMD Athlon XP 1800+ Socket A
Graphics card : Abit Ge Force 4 TI 4200 64 Mo DDR
RAM :DDR 512 Mo KingElephant

So, I must shut down, remove switch Bios and put back( whitout any change).

And I have now the same thing : cmos settings wrong, etc...

I write MSI And I wait there response.

Thank you to help me
Denniss
BIOS Guru
Posts: 3153
Joined: Thu Mar 21, 2002 8:16 pm
Location: Near Hannover (CEBIT) Germany
Contact:

Tried to load Setup Defaults or Optimal/Performance Settings in Bios and then save and exit ?

Is this a new error or does it come since you have this board ?
mkmir
New visitors - please read the rules.
Posts: 2
Joined: Thu Oct 31, 2002 4:14 pm

Thanks for your replay,

But I can't save any change in SETUP BIOS. When I change, and put F10 to save, computer wouldn't reboot. So, I must remove jumper of CMOS and, I have the same Bios Settings.

Merci bien

mkmir
Denniss
BIOS Guru
Posts: 3153
Joined: Thu Mar 21, 2002 8:16 pm
Location: Near Hannover (CEBIT) Germany
Contact:

Is it possible to Load the Defaults in Bios and change FSB and memory clock back to 100MHz ?
If this is working try FSB100 and memory 133 next .
Check the PSU voltages/ CPU temps in Hardwaremonitor section of your Bios - maybe named CPU or System Health .
If you have two sticks of memory use only one to test .
Denniss
BIOS Guru
Posts: 3153
Joined: Thu Mar 21, 2002 8:16 pm
Location: Near Hannover (CEBIT) Germany
Contact:

And make sure you have your CPU cooler mounted in the correct way !
ChameleonTPC
New visitors - please read the rules.
Posts: 2
Joined: Sun Mar 21, 2004 12:55 am

If all else fail then this is a hardware issue. Very much like the K7S5A I put back to life. Of course with the help of Uniflash and a little tinkering !
Vladutz
New visitors - please read the rules.
Posts: 1
Joined: Wed Jan 11, 2006 9:27 am

Could anyone expand on Uniflash and a little tinkering? I have the exact same problem with my K7S5A.

Thank you
boogie
New visitors - please read the rules.
Posts: 1
Joined: Sat Jan 14, 2006 9:04 pm

im also having the same problem with my K7S5A board...it wont boot up properly, it takes numerous attempts until it finally starts up...it give me errors saying CMOS Settings Wrong and CMOS Memory Size Wrong....any way to fix these problems? thank you
SAADMOON
New visitors - please read the rules.
Posts: 2
Joined: Mon Jan 30, 2006 9:48 pm

mkmir wrote:Help!!!!!!!

First, excuse my Bad english.

Probleme : when I switch on my computer, I have this message : CMOS SETTINGS WRONG. If I put F2 ( load defaults sttings), that's ok. Winxp and all programs.

But if I put F1 ( modifie bios setup), and F10 ( whitout any chanage), My computer doesn't switch on ( it's blocked). Whitout any message.

Of course, I changed Bios, but always the same thing.

I have this configuration

MC : MSI KT3 Ultra2 Socket A VIA KT333
Processor : AMD Athlon XP 1800+ Socket A
Graphics card : Abit Ge Force 4 TI 4200 64 Mo DDR
RAM :DDR 512 Mo KingElephant

So, I must shut down, remove switch Bios and put back( whitout any change).

And I have now the same thing : cmos settings wrong, etc...

I write MSI And I wait there response.

Thank you to help me
Ritchie
BIOS Guru
Posts: 761
Joined: Wed Oct 30, 2002 5:17 am

I suspect a buggy BIOS. Especially if three people have the same problem there is likely to be something other at stake than faulty hardware.

It would be interesting to know what BIOS versions everyone is running off, and then for someone willing to try a different BIOS version and see if OK. If everyone running recent BIOS versions maybe bugs in recent ones.

Possibly also if there are diffferent PCB versions and everyone running recent BIOS, that BIOS updates were made available by the manufacturer without documenting that certain releases applied to certain PCB versions.
Post Reply