BIOS Updates forum

Yes I am fitting it the correct way.

The s775 has a couple of the pins askew and the top of two of them
have the contact fingers amiss i.e. the top 0.5mm

I got this board second user - can the s755 be replaced?

Hi Have an ECS RC410-M2 v1.0 motherboard. No case. I believe it to be an OEM version, possibly Packard Bell. 1. I am aware, PB use this board in their PC product line so far as they refer to using an ECS RC410 in the iStart PC from 2006; 2. But I cannot find any reference to an RC410 on the ECS webs...

Hi I suspect the CPU socket on this motherboard has gone. So far as I have seen quoted, the s775 is only good for 20 insertions, the socket on this board appears iffy. I have tried a quick exercise to get the pins straight but consider unlike prior to where I have been able to get a CPU working agai...

Hi, RE - reading and flashing in place You state this can be done where no other peripherals are in expansion (PCI, AGP) slots, no CPU is installed, no drives are installed and no PSU attached to the system. Are you sure a read/write in this manner will not damage the mobo? Whereas I conceive damage...

yep - oops...sorry

Thx

These are ready made and very cheap

PLCC32 To DIP32
http://www.sivava.com/image_B01.htm

Adapter FWH/PLC To DIP32
http://www.sivava.com/image_B03.htm

Yes, its guess the mobo question again I suspect this mobo is a Gigabyte by the colour and decals on PCB. However, Gigabyte have no Radeon Express 200 mobos on their site. AMD state they do per; http://ati.amd.com/buy/promotions/radeonxpress200/intel.html On the Gigabyte site we have - GA-8TRS300M h...

I would like to get an image from it by reading it first. As I do not yet know the OEM for this mobo but suspect it is eMachines, to do this first is priority. This depends of course on the fact, if the board is dead becuase of a prior bad flash - reading the image would be no use. I believe I requi...

The part is a FWH/LPC type, an Atmel AT49LH004

http://pdf1.alldatasheet.com/datasheet- ... LH004.html?

These only require 3.3V

Yeah - flash intermittently. BIOS device soldered to board. Q - I have a Willem but was of the opinion the device would have to be removed prior to reading the BIOS image or re/hot flashing. I have seen advice some of the low voltage flash pieces such as with 5V and 3.3V can be read/flashed in situ....

Nothing more recent than a Magna 600W 20 pin ATX

Also have a dated QTEC 20 pin ATX
http://www.qtec.info/products/product.htm?artnr=13023

Haven't tried these yet

Thx E Finding further BIOS would be nice if any are available. The extract from detect follows; Program: eSupport.com BIOS Detect v1.2 July 21, 2003 BIOS Date: 10/29/04 BIOS Type: Phoenix - AwardBIOS v6.00PG BIOS ID: 10/29/2004-Grantsdale-6A79DM4GC-00 OEM Sign-On: W7046M7 V3.05 102904 15:30:00 DIXON...

Magna 600W ATX 20 pin PSU Board Dead - no cpu fan PSU Fans spin up ok Keybard LEDs flash intermittently that is Caps lock, Scroll and Number lock. Mobo Front Panel switch does not switch on the mobo. No activity on POST CARD seven segment display but POST Card LEDs report; Sys - Flashes Clk - On I/O...

Resolved this issue

I got the mobo to run and found it was a DIXONPC OEM BIOS
I am making enquiries into whether (not) a BIOS update is available.

Board appears to be ok

As it turns out this board is a K7N2 Delta-ILSR

It is not a OEM but an MSI board
The previous POST code was misleading

Got the most recent BIOS, flashed, mobo works - good