Page 1 of 2
Video resolution problems
Posted: Sat Apr 02, 2005 5:04 pm
by Specter
Hi everyone,
New on this forum.
I'm not sure to post in the right place but I'm wondering if anyone can help me about a problem:
I had a monitor 800 x 600 resolution on SiS 530 hardware.The monitor was out and I bought a new one with 1024 x 768 resolution,but now I've a low quality image:the monitor is full enlighted but the image resolution is low as the image appears "raw",more than the old monitor.
I downloaded the updated driver from the web but without results;
Doesn't SiS 530 support 1024 x 768 resolution?
Have I to set something in the BIOS?
Have I to set something in the screen settings ?
Any helpful advice will be appreciated!
Thanks in advance.
Regards
Posted: Sun Apr 03, 2005 5:20 am
by ajzchips
Sure it supports it. Perhaps you need to select a different refresh rate.
Posted: Mon Apr 04, 2005 2:23 pm
by Specter
Done.Nothing happens...
Further Suggestions? Advices?
Thanks in advance.
Bye
Posted: Mon Apr 04, 2005 4:28 pm
by soupy
This is onboard, right? How much memory is allotted? What color depth and refresh rate are you attempting?
Posted: Mon Apr 04, 2005 4:38 pm
by Specter
Hi,
This is onboard, right?
What do you refer?
However,my current settings are:
800 x 600 resolution
16.8 millions of colors (32 bit)
refresh frequency
AUTO (I tried all the supported frequencies...)
memory
8 Mb (my BIOS doesn't allow more...)
Thanks for interesting
Bye
Posted: Tue Apr 05, 2005 7:00 pm
by Denniss
Try 16-Bit colours
It's possible the RAMDAC is of low quality thus having bad image quality on higher resolutions.
Posted: Sat Apr 09, 2005 6:48 pm
by Specter
Sorry,
No 16 bit colours
only 256 63,000 16,000,000 colours
The problem is still there...
Posted: Sun Apr 10, 2005 2:30 pm
by KachiWachi
What monitor?
Posted: Sun Apr 10, 2005 2:52 pm
by Specter
EIZO Flex Scan F 35
Posted: Mon Apr 11, 2005 2:33 pm
by KachiWachi
FlexScan® F35 ->
http://www.eizo.com/support/discontinued/crt/f35.asp
This monitor has DDC...is is correctly identified in the Device Manager?
Posted: Mon Apr 11, 2005 6:58 pm
by Specter
I think it isn't.
As I don't know what is DDC...
Posted: Tue Apr 12, 2005 2:26 pm
by KachiWachi
OS?
What does the Device Manager say about the Display Adapter and Monitor?
Posted: Tue Apr 12, 2005 6:44 pm
by Specter
Windows 98 SE
What does the Device Manager say about the Display Adapter and Monitor?
Huh? What's device manager and display adapter monitor?
Please ,answer me.
Thanks
Posted: Wed Apr 13, 2005 3:07 am
by Ritchie
If memory serves well, in Windows 98, device manager is one of the tabs under the System icon in Control Panel.
Device Manager will show you a detailed list of internal and external devices Windows has identified and installed. There will be a display category and should be a monitor category. If you open these categories up you can see the name of the installed device (which device manager thinks is correct - sometimes the wrong device may be installed. However at this point and for your purposes the information can be considered accurate for now).
Posted: Tue Apr 19, 2005 8:08 pm
by Specter
Thanks for the answer Ritchie.
I found the device manager and it displays a generic "Plug&Play" monitor with a generic "Microsoft" driver.
So,I think there is a problem,but how can I solve it?
I already attempt to install the monitor driver but this shows that I made some mistake.
How can I do?
Hoping you come across this thread...
Otherwise I appeal to anyone able to address me on the right way.
Thanks
Bye